Please search and download "Amaryllo AI" APP to get started.
★ Make sure your smart phone is connected to the same Wi-Fi network
3. Power on the device
Turn off the light switch. This will prevent you from being electrocuted.
Screw in the device by placing it into socket then gently turn clockwise until it is secure.
Rotate in a counterclockwise direction to the desired viewing angle. Do not overpower the stopper when the device rotates to the end.
CAUTION: When fixing the device to the socket, DO NOT APPLY EXCESSIVE FORCE WHEN INSTALLING, otherwise, it might cause damage to the device and the light bulb socket.
Please use the included clips to secure your light bulb socket if needed.
Would like to remove it.Firstly, you must wait the lamp cooling if you
LED light will turn on indicating it is powered on.Turn on the light switch, after which the blue installation.
After power-on, wait for it to start flashing before beginning the 25 seconds to start calibration cycle.
4. Setup camera in the APP
Select AR2 in the APP then follow the instructions shown.
★ Please refer to the FAQ page for more info on how to share the viewer or administrator rights to other smart phone devices.
5. Connect camera to the Internet
Please make sure that your smart phone is connected to the same Wi-Fi SSID network.
After selecting AR3S, you will be given Internet setup options.
Select Auto-Detection (Recommended)
6. Select AMID to complete setup
Tap on the AMID to complete auto setup.
Note: AMID can be found on the bottom of the device. Make sure the AMID is the same as one which appears in APP setup.
7. App setup complete
The green LED remains on when Wi-Fi is working properly.The device setup is complete. You will hear two beeps when thedevice setup completes.
Congratulations!Your AR2 is set up and ready to go.
Note: The camera is designed for easy DIY installation but if you need local assistance, please visit www.SoteriaAi.com to locate a professional installer near you.
★ Please be sure your device is running on the latest firmware.
★ User QR code to setup device
Make sure your phone is connected to the same Wi-Fi router as your camera.
A QR code will be generated when you enter in the Wi-Fi password.
Your device will automatically generate a QR code.(20~30 cm) in front of tablet’sQR code. Place the device 4” ~11.8” (10~30 cm) in front of the QR code or 7.8” ~11.8”
Show the QR code to the camera. You will hear a beep sound when setup is successful.
★ You may sit the camera on a surface
★ LED indicator
Blue LED The LED is stable when you power on the device. The LED flashes once per second when the QR scan is in progress. When LED is flashing twice per second, the device is in use and someone is actively viewing it. When LED is flashing 3 times per second, the setup process was successful.
Green LED: When LED is flashing once per second, the device is trying to connect to a Wi-Fi AP router. When LED is constant, the device is connected to Wi-Fi and working properly.
★ Factory reset
First, make sure the device is powered on and the calibratio is completed.
There is a small RESET hole. Press and hold for about 5 seconds until the blue LED flashes. All settings of previously stored in the device will be erased, and it will be restored to the factory default.
After 25 seconds, the device will start a calibration mode by rotating itself. (for remote models)
★ Add another Wi-Fi source
Connect your phone to your router.
Press and hold the router’s WPS button.
Press and hold WPS button on the device for 5 seconds or longer. When the green LED flashes, it indicates that the device has entered WPS mode.
Please follow App instructions step-by-step.
Note: You need to press WPS button of the device and Wi-Fi AP router within 60 seconds. (Using a paper clip)
Note: Indoor use only
★ Need help? Visit http://www.amaryllo.eu/support or drop us an email with photo or video and description of the problem to firstname.lastname@example.org